home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
IRIX Patches 1995 December
/
SGI IRIX Patches 1995 Dec.iso
/
relnotes
/
patchSG0000862
/
ch1.z
/
ch1
Wrap
Text File
|
1995-11-17
|
5KB
|
199 lines
- 1 -
1. _P_a_t_c_h__S_G_0_0_0_0_8_6_2__R_e_l_e_a_s_e__N_o_t_e
This release note describes patch SG0000862 to IRIX 5.3.
1.1 _S_u_p_p_o_r_t_e_d__H_a_r_d_w_a_r_e__P_l_a_t_f_o_r_m_s
All platforms.
1.2 _S_u_p_p_o_r_t_e_d__S_o_f_t_w_a_r_e__P_l_a_t_f_o_r_m_s
This patch contains bug fixes for IRIS Token Ring (version
1021572033 ) on a system running IRIX 5.3 (versions
1021572036). The software cannot be installed on other
configurations.
1.3 _B_u_g_s__F_i_x_e_d__b_y__P_a_t_c_h__S_G_0_0_0_0_8_6_2
This patch contains fixes for the following bugs in IRIX
5.3. Bug numbers from Silicon Graphics bug tracking system
are included for reference.
+o On a rare race condition, llc2.a could cause kernel
panic (BUG# 265294.) When it happens, it dies at
llc2_wput() routine.
+o Netsnoop crashed kernel on VME token ring interface,
if_fv (BUG# 265316.) Promiscuous mode is not supported
in the driver. The use of promiscuous mode is now
turned off.
+o Token Ring driver and DLPI driver not properly
receiving SNAP packets (BUG# 294316.)
+o Token Ring driver may crash the system while idle state
(BUG# 296164.)
1.4 _S_u_b_s_y_s_t_e_m_s__I_n_c_l_u_d_e_d__i_n__P_a_t_c_h__S_G_0_0_0_0_8_6_2
This patch release includes these subsystems:
+o patchSG0000862.tokenring_sw.tokenring
+o patchSG0000862.eoe1_sw.dlpi
- 2 -
1.5 _I_n_s_t_a_l_l_a_t_i_o_n__I_n_s_t_r_u_c_t_i_o_n_s
Because you want to install only the patches for problems
you have encountered, patch software is not installed by
default. After reading the descriptions of the bugs fixed
in this patch (see Section 1.3), determine the patches that
meet your specific needs.
If, after reading Sections 1.1 and 1.2 of these release
notes, you are unsure whether your hardware and software
meet the requirements for installing a particular patch, run
_i_n_s_t. The _i_n_s_t program does not allow you to install
patches that are incompatible with your hardware or
software.
Patch software is installed like any other Silicon Graphics
software product. Follow the instructions in your _S_o_f_t_w_a_r_e
_I_n_s_t_a_l_l_a_t_i_o_n _A_d_m_i_n_i_s_t_r_a_t_o_r'_s _G_u_i_d_e to bring up the miniroot
form of the software installation tools.
Follow these steps to select a patch for installation:
1. At the Inst> prompt, type
iiiinnnnssssttttaaaallllllll ppppaaaattttcccchhhhSSSSGGGG_x_x_x_x_x_x_x
where _x_x_x_x_x_x_x is the patch number.
2. Initiate the installation sequence. Type
IIIInnnnsssstttt>>>> ggggoooo
3. You may find that two patches have been marked as
incompatible. (The installation tools reject an
installation request if an incompatibility is
detected.) If this occurs, you must deselect one of
the patches.
IIIInnnnsssstttt>>>> kkkkeeeeeeeepppp ppppaaaattttcccchhhhSSSSGGGG_x_x_x_x_x_x_x
where _x_x_x_x_x_x_x is the patch number.
4. After completing the installation process, exit the
_i_n_s_t program by typing
IIIInnnnsssstttt>>>> qqqquuuuiiiitttt
- 3 -
1.6 _P_a_t_c_h__R_e_m_o_v_a_l__I_n_s_t_r_u_c_t_i_o_n_s
To remove a patch, use the _v_e_r_s_i_o_n_s _r_e_m_o_v_e command as you
would for any other software subsystem. The removal process
reinstates the original version of software unless you have
specifically removed the patch history from your system.
vvvveeeerrrrssssiiiioooonnnnssss rrrreeeemmmmoooovvvveeee ppppaaaattttcccchhhhSSSSGGGG_x_x_x_x_x_x_x
where _x_x_x_x_x_x_x is the patch number.
To keep a patch but increase your disk space, use the
_v_e_r_s_i_o_n_s _r_e_m_o_v_e_h_i_s_t command to remove the patch history.
vvvveeeerrrrssssiiiioooonnnnssss rrrreeeemmmmoooovvvveeeehhhhiiiisssstttt ppppaaaattttcccchhhhSSSSGGGG_x_x_x_x_x_x_x
where _x_x_x_x_x_x_x is the patch number.
1.7 _K_n_o_w_n__P_r_o_b_l_e_m_s